nbn™ logo (large)

nbn introduces DOCSIS 3.1 NTDs this month

No high-speed tiers to accompany launch of higher speed network

The company responsible for building the National Broadband Network, nbn, is set to begin installing new HFC Network Termination Devices (NTDs) at the end of this month to allow them to connect to the upgraded DOCSIS 3.1 network.

nbn’s NTD is a customised CM8200B DOCSIS 3.1 modem from Arris, who successfully won a tender to supply the network equipment.

nbn's new HFC Network Termination Device capable of DOCSIS 3.1
nbn’s new HFC Network Termination Device capable of DOCSIS 3.1 (Source: nbn co)

nbn had initially planned to begin deploying its DOCSIS 3.1 NTDs in December 2016. This has been pushed back by a month to the end of January 2017, with the company issuing an amendment to its Wholesale Broadband Agreement (WBA2).

In their notification letter to Access Seekers, nbn states that it intends to “introduce the new CM8200B (DOCSIS 3.1) HFC-NTD deploying on all HFC installations from end January 2017”.


No speed increase despite upgrade

Despite touting the speed capabilities of the new DOCSIS 3.1 modems, nbn will not launch new speed tiers to accompany the launch of the new modems.

In November 2015, nbn’s Chief Technology Officer penned a blog post saying that new modems by Arris will be capable of delivering “a stunning 5Gbps downstream and 2Gbps upstream”.

However, the maximum speed tier nbn will offer over the HFC network will remain at 100/40 Mbps. The January 2017 Integrated Deployment Plan also shows no future plans to introduce higher speed tiers already available the NBN Fibre network.

DOCSIS 3.1 promises to provide improved network performance and speeds through increased modulation orders and wider spectrum utilisation.

The new NTD will also have a second Ethernet port, however, the port will be disabled and covered by a sticker at launch.

Inside an NBN node at Umina Beach

NBN: 5 drop outs daily “acceptable” on new FTTN network

Leaked internal documents detailing the fault resolution process on the FTTN/B network suggests a nightmare process awaits millions of Australians

A leaked document from the company responsible for building the National Broadband Network (nbn) has revealed insights into the fault ratification process for its Fibre to the Node and  Basement networks.

The freshly leaked document, first published by technology publication Delimiter, is the latest addition to a string of damaging leaked documents from within the company within the last few weeks alone.

5 drops out a day? That’s “acceptable”

Australians shouldn’t expect their current unexpected drop-outs to be fixed after upgrading to the new Fibre to the Node network.

On page 21, nbn describes how it plans to diagnose a user experiencing drop-out issues on the Fibre to the Node and Fibre to the Basement networks.

A user experiencing on average 2.4 resync events (colloquially known as dropouts) per day as being connected to a “stable” connection. It goes on to explain that connections experiencing up to 5 dropouts a day as being “risky” — yet “nbn regards risky [connections] as acceptable”.

NBN considers 5 drop outs per day as "acceptable"
NBN considers 5 drop outs per day as “acceptable”

The company suggests putting risky connections into a lower sync speed by assigning them to a “stability” profile in the hope of reduced drop-out rates.

Modems must be approved, or faults cannot be logged

The NBN company is insisting that end users must use an approved modem, certified to be working by an NBN service provider, in order for a fault to be lodged.

Despite the requirement of an approved modem, nbn has refused a freedom of information request to provide a list of modems that are approved for connecting to the NBN network to the public. Nor can members of the public request models of modems to be tested for registration.

This forces all end users to purchase the low-end, consumer-grade modem approved by their service providers such as the cheap sagecomm f@st modem line-up preferred by some major carriers. The flaw in this is that many sagecomm modems have a ton. of. security.exploits.

$50 No Fault Found charge if problem is beyond the network boundary

Unlike on its fibre network, nbn will charge end users $50 for a “No Fault Found”call-out fee for the FTTN and FTTB network where the technician identifies no faults on the line or if the fault is within the end user’s house (for example, a bridge tap inside the home).

This fee, similar to one currently charged by Telstra, is set to discourage end users from lodging faults and risk paying a $50 No Fault Found charge if a fault is not identified.


So here we are again, folks:

  • It’s okay for this new $56 billion dollar network to drop out 1, 2… maybe 5 times a day — that’s totally acceptable!
  • You’re after a modem that’s higher quality, possibly enterprise-grade, instead than the cheapo modem your service provider sold to you? Not only will we not tell you what modems you can get, you can’t even get new modems approved if you wanted!
  • Finally, think you have a fault? Think again — we can slug you $50 if you complain about the network and we don’t find anything wrong with it!

What a wonderful broadband network this is going to be!